FC100 Fiber Optic Converter
Lightning Protection
Long-term, trouble-free protection for your data logger
weather applications water applications energy applications gas flux and turbulence applications infrastructure applications soil applications

Overview

The FC100 is typically used with the SG000 Strike Guard Lightning Detector as part of the CS110 and LW110 lightning warning systems. The SG000 outputs its data signal via fiber-optic cable, and the FC100 is installed at the end of the fiber-optic cable and before the data logger. The FC100 converts a fiber-optic data signal into an RS-232 signal for a lightning-proof connection between the sensor and the data logger.

The FC100 can also be used as an RS-232 link between two serial devices (data logger to PC) separated by less than 100 m (328 ft). The FC100 is a DCE device so a null modem cable will be needed between it and a data logger.

Read More

Benefits and Features

  • Lightning-proof and lightning-safe serial communication
  • Robust design for long, trouble-free operation
  • Instant termination without connectors, crimping, polishing, or epoxy

Images

Detailed Description

The FC100 is designed for use with the SG000 Strike Guard lightning detector as part of the CS110 lightning warning system. The SG000 outputs its data signal via fiber-optic cable, and the FC100 is installed at the end of the fiber-optic cable and before the data logger. The FC100 converts a fiber-optic data signal into an RS-232 signal for a lightning-proof connection between the sensor and the data logger.

The FC100 can also be used as an RS-232 link between two serial devices (data logger to PC) separated by less than 328 ft (100 m). The FC100 is a DCE device so a null modem cable will be needed between it and a data logger.

Specifications

Electrical Connector 9-pin, D sub, DTE compatible
Baud Rates 1,200 to 19,200 bps (at 100 m guaranteed with FC100CBL-L cable)
Power 12 Vdc (via pn 14291 or pn 15966)
Current 5 mA (average)
Mounting Holes 7.62 cm (3 in.) apart
Case Width 2.8 cm (1.1 in.)
Dimensions
  • 9.0 cm (3.5 in.) from the ends of the mounting bracket
  • 5.6 cm (2.2 in.) from the bottom of the case to the top of the screw on the top of the case

Compatibility

Note: The following shows notable compatibility information. It is not a comprehensive list of all compatible or incompatible products.

Data Loggers

Product Compatible Note
CR1000 (retired)
CR1000X
CR200X (retired)
CR206X (retired)
CR211X (retired)
CR216X (retired)
CR295X (retired)
CR300
CR3000 (retired)
CR310
CR350
CR5000 (retired)
CR6
CR800 (retired)
CR850 (retired)
CR9000X (retired)

Additional Compatibility Information

The FC100 is used with the SG000 Strike Guard.

Documents

Frequently Asked Questions

Number of FAQs related to FC100: 10

Expand AllCollapse All

  1. Are there any precautions to take when using the FC100?
    The data transmission fibers are fragile and cannot be bent or broken. Consequently, the fibers need to be handled with care and protected inside a conduit (usually PVC).
  2. Are there any troubleshooting tips for the FC100?
    Short-fiber runs sometimes pass too much signal. The solution is to pull the fiber part way out of the holding ferrule.
  3. Why does the FC100 require the 14291 or 15966 12 Vdc supply?
    The 12 Vdc power supply keeps the signal from dropping when large data packets are transmitted.
  4. What baud rates are available with the FC100?
    With a good signal strength, 1200 to 19,200 bps.
  5. What are the advantages of the FC100 as compared with other fiber modems?
    The FC100 provides instant termination—no connectors, crimping, polishing, or epoxy.
  6. How far can data be transmitted with an FC100?
    100 m (330 ft) with a 1.0 mm poly-methylmethacrylate (PMMA) core with a PVC or polyethylene jacket, simplex or duplex; up to 1 km with a higher-grade fiber.
  7. What is the FC100 used for?

    Direct communication between two RS-232 serial devices, such as a PC to a data logger or a data logger to a serial sensor.

  8. Which applications are better suited to using an FC100 rather than an SRM-5A Short Haul RAD Modem?
    The FC100 is designed for lightning-proof and lightning-safe serial communication. Because the FC100 offers PMMA or glass fibers that are not conductive, electrical surges (such as those caused by lightning) cannot travel between the modems.
  9. What is the FC100 commonly used with?
    The FC100 is required to communicate with the SG000 Strike Guard Lightning Sensor. The SG000 is an option for the CS110 Electric Field Sensor and the LW110 Lightning Warning System.
  10. What are the advantages of fiber modems?
    They provide lightning-proof and lightning-safe serial communication that eliminates the need for transient suppression devices.
Visit the FAQ Library

Listed Under

Common Accessory for the following products:

Privacy Policy Update

We've updated our privacy policy.  Learn More

Cookie Consent

Update your cookie preferences.  Update Cookie Preferences